
J-14 PowerActive
14′ 5″ · jet current
10′ 7″ of open water

No manufacturer pays us. How we make money
The lane is 2′ 5″ shorter than you are stretched out, before a kick.
Arctic Spas doesn't say whether air is mixed in or whether the pumps run only the current, so ask the dealer.
How currents compare →Lap swimmers like 78 to 82°F and a hot tub runs 100 to 104, so you pick a compromise or change the setting and wait.
Is dual temperature worth it →No California listing we could match
California lists what a spa draws on standby, with the cover on. We found no listing that matches this model. No Arctic Spas swim spa has one.
What they like
A tether-only layout that suits slow, steady swimmers
A retired couple shopping in 2019 said that after wet-testing several brands, whose currents pushed them into walls and seats, the Athabascan's open, current-free 14-ft layout for tethered swimming was the only design that fit what they wanted. A shopper's view before purchase, not an owner report.
What they complain about
Dealer and service coverage is patchy in places
The same 2019 shopper found no Arctic dealer, showroom or service in Northern California; the nearest contact was in Spokane, and two forum respondents, one a long-time member, advised against buying a large-ticket spa without local dealer support.
Called pricey for a 14-ft swim spa
In a 2014 thread comparing a Wolverine with another brand, three posters, one of them a dealer, called Arctic overpriced or 'a lot of money' for a 14-ft swim spa, while an Arctic dealer in the same thread called the shopper's quoted price a very good deal; in the 2019 thread a poster whose account name suggests a distributor called Arctic's swim spas overpriced and short on swimming power. Opinions without price or flow data.
These findings cover the Arctic Spas swim spa line; each names the models it applies to.
240 V on 6-gauge wire, one breaker per configuration: 1 pump, 32 A on a 40 A breaker; 2 pumps, 40 A on 50 A; 3 pumps, 40 A on 50 A; 4 pumps, 48 A on 60 A. On 115 V and 14-gauge wire: 1 pump, 12 A on 15 A. The same table, including the 115 V/15 A row, is printed for Arctic's hot tubs; the TÜV SÜD listing shows only 230 V configurations for All-Weather Pools. TÜV SÜD certificate U8 056165 0071 Rev. 04 (60 Hz, June 10, 2024) rates this model's configurations as follows, with amps as draw: Prestige, 230 V, 20 jets, 2.5 HP, 24/32/40 A, 5,500 W heater; Prestige SDS, 2.5/3 HP, 24/32/40/44 A; Signature, 40 jets, 2.5/3 HP, 24/32/40/44 A; Signature SDS, 2.5/3/3 HP, 24/32/40/48 A; Legend, 40 jets, 2.5/3/3 HP, 24/32/40/48 A; Legend SDS, 2.5/3/3/3 HP, 24/32/40/48 A. The manual says to wire it to the rating on the certification label beside the control pack and warns that bypassing the GFCI/RCD voids the warranty.
Arctic Spas’s own documents give two answers. Check yours against the quote before you sign.
Length
172" (14′ 4″)
arcticspas.com ↗171" (14′ 3″)
arcticspas.com ↗Width
93" (7′ 9″)
arcticspas.com ↗94.5" (7′ 10.5″)
arcticspas.com ↗Height
Ten things that decide whether a swim spa works for you and lasts, answered for Arctic Spas’s swim spas. Tap any for the detail.
Arctic uses two jet systems: the Monsoon, six stacked high-volume jets standard on the Ocean, Columbia, Okanagan, Hudson and Polar Bear, and the Niagara, an aimable jet it says moves water at up to 27 feet per second, on the Wolverine and Kingfisher. Every model also has a swim tether, and Arctic itself pitches the jets for intermediate swimmers and the tether for advanced ones. It publishes no flow rate, no speed settings and nothing on air injection.
What this means, and how to check it →arcticspas.com ↗arcticspas.com ↗
Each product page has a 'Swim Area Specifications' drawing with a printed length and width, which only some makers offer. On the seven 14-foot models the lane runs from 98 in (Columbia) to 144 in (Hudson), all 50 in wide, and the 18-foot Polar Bear gives 165 by 67 in, or 144 by 50 in with the Niagara Turbo upgrade. Arctic prints only the 51-inch cabinet height, so ask how deep the water is.
What this means, and how to check it →arcticspas.com ↗arcticspas.com ↗
Arctic backs its acrylic with hand-applied, filler-free fiberglass and says the shell holds itself up with no beams or props; a rival maker's comparison also says Arctic's swim spas have no frame. The Ocean, Columbia, Okanagan and Polar Bear come with the SMC fiberglass Forever Floor, while the Hudson, Wolverine, Kingfisher and Athabascan get a pressure-treated wood platform floor unless you pay for the upgrade. Arctic publishes no laminate thickness or frame detail for its swim spas.
What this means, and how to check it →arcticspas.com ↗arcticspas.com ↗
Arctic's manual says an All-Weather Pool must sit on a uniformly solid, level surface rated for at least 146 lb per square foot, such as a concrete pad or properly engineered deck (never lawn, bare ground or gravel), with 24 inches clear on every side. Its technical pages add that a crane is required, and the Forever Floor's no-pad promise doesn't apply to swim spas. Wiring is one 240-V breaker: 40 A for one-pump builds, 50 A for the two- and three-pump builds of the Ocean, Columbia, Okanagan and Polar Bear, and 60 A for four-pump builds and for the Wolverine (three pumps) and Kingfisher (two pumps); the three-pump Hudson's breaker size isn't published.
What this means, and how to check it →arcticspas.com ↗arcticspas.com ↗
Arctic insulates the cabinet walls and floor (its blog says 3-4 inches of 2 lb foam) and leaves the equipment foam-free so pump heat warms the water; every All-Weather Pool ships with a 5-to-4-inch tapered Mylovac cover (6-5-4 on the Polar Bear). We found no California energy listing for any Arctic swim spa, and Arctic's 'California Energy Commission compliant' line comes without figures. Arctic doesn't explain its CoolMode for hot weather, so ask the dealer.
What this means, and how to check it →arcticspas.com ↗arcticspas.com ↗
Arctic's lineup has no divided or dual-temperature swim spa, so you choose one temperature for swimming and soaking, or change it and wait. Seating runs from none on the Kingfisher to six seats on the Ocean and Columbia, all in the shared water. With one heater and one control pack there's only one set of equipment to maintain.
What this means, and how to check it →arcticspas.com ↗arcticspas.com ↗
Arctic's Total Access cabinet and perimeter insulation leave the pumps, heater and plumbing free of foam, and the owner's manual says the spa has access doors on all four sides that must stay reachable with at least 24 inches of clearance. Its hose is glued over rigid PVC and, Arctic says, can usually be repaired with a clamp, but union-connection leaks are excluded from the warranty as owner-serviceable. The warranty won't pay to remove a deck, sunroom or gazebo or for a crane.
What this means, and how to check it →arcticspas.com ↗arcticspas.com ↗
Arctic's 2026 manual puts the Ocean and Okanagan under its Custom card (lifetime shell, 5 years on surface, equipment and plumbing) and the Hudson, Wolverine, Kingfisher and Athabascan under its Classic card (10-year shell, 4-year surface, 3-year equipment); it doesn't say which card covers the Columbia or Polar Bear. Both cards cap warranty labor at $60 per approved claim, charge travel after the first 30 days, leave removal and crane costs to you, exclude freeze damage and end when the spa is sold. No card lists the swim system separately.
What this means, and how to check it →arcticspas.com ↗arcticspas.com ↗
Every All-Weather Pool ships with a Mylovac foam cover tapering 5 to 4 inches (6-5-4 on the Polar Bear), vacuum-sealed around double-density foam with a metal channel, locking straps and wind flaps, and the manual calls it a locking safety cover meeting ASTM F1346-91. Arctic doesn't publish how many sections it has or what it weighs, sells lifters separately, and gives the cover 3 years, parts only, counting seam damage from a lifter as normal wear. Lift a panel in the showroom.
What this means, and how to check it →arcticspas.com ↗arcticspas.com ↗
Arctic says its spas are manufactured in Canada and the United States and sells through a dealer network it puts at more than 300 worldwide; warranty work must be done by a factory-authorized dealer and applies only where the spa was first installed. A 2019 forum shopper in Northern California found no Arctic dealer nearer than Spokane, so confirm a local technician before buying. An asset auction at the Thorsby site closed on September 22, 2026; all eight model pages were still online on September 27, 2026.
What this means, and how to check it →arcticspas.com ↗arcticspas.com ↗
What Arctic Spas leads with, where it covers the Okanagan, and what the documents show.
What they sayArctic pitches the All-Weather Pool as a backyard pool you can be swimming in the day after delivery: set on a prepared concrete pad, a fraction of an in-ground pool's cost, and no spring opening or fall closing.
What the documents showSkipping excavation and seasonal openings is real for any swim spa. But Arctic's own pages say a crane is required and the pad must be built for the load, and Arctic publishes no price to back the 'fraction of the cost' line.
Who else does itEvery swim spa maker sells the pool-alternative idea; it isn't specific to Arctic.
What they sayFreeHeat perimeter insulation traps pump heat around the shell and protects the plumbing from freezing if the power fails, so the pool runs all year in a cold climate ('Engineered for the World's Harshest Climates').
What the documents showRecycling motor heat and keeping the plumbing foam-free are real design choices, and a rival maker's comparison agrees the foam traps heat. But Arctic publishes no standby-watt figure or freeze test for its swim spas, and there's no California energy listing for any of them.
Who else does itPerimeter insulation is not unusual among swim spas: Cal Spas, PDC, Wellis, Dynasty and American Whirlpool use it too. What Arctic stresses is foam on the cabinet floor as well as the walls, and a rival maker's 2024 comparison says it thinks Arctic is 'the only one out there' doing that.
What they sayEvery All-Weather Pool includes the Tether Resistance System, which Arctic says was designed by professional athletes and gives 'unlimited variable resistance for advanced swimmers', alongside a Monsoon or Niagara jet current on seven of the eight models.
What the documents showThe 2026 brochure marks the tether standard on all eight models, and a tether gives a strong swimmer a full-effort workout in still water.
Who else does itA few other makers also include a tether as standard: Sundance lists a 'Swim Tether Cord – (included)', PDC ships an 'AquaCross™ Tether Trainer' on most of its models and Dynasty includes one on some; Hydropool's comparison says it offers one only as an option. Most makers we researched list no tether as standard equipment.
Partly a catch
The tether does the hard work: Arctic itself rates its jets 'medium resistance'. Arctic's own page says its swim jets give 'medium resistance for intermediate swimmers', its blog calls the Hudson's current 'entry-level', and the Athabascan has no current at all. Arctic publishes no flow, speed or horsepower-to-current figures.
What they sayEach product page shows a 'Swim Area Specifications' drawing with the open swim area's length and width, for example 144 by 50 in on the Hudson and 165 by 67 in on the Polar Bear.
What the documents showThe figures are printed on Arctic's own pages for all eight models, so buyers can compare lanes rather than cabinet sizes.
Who else does itSeveral makers publish a swim or fitness area (PDC, Hydropool, Jacuzzi, Cal Spas and Sundance among them). Arctic's version is a drawing on every product page that outlines the open water and prints both its length and width.
The catch
The lanes are short on most 14-ft models, and depth is missing. The six-seat Ocean and Columbia leave 100 and 98 inches, the Okanagan's printed length is 55 inches, and every 14-ft lane is 50 inches wide. The outlined areas taper between the seats, Arctic's 'longest swim zone' Kingfisher prints 126 inches against the Hudson's 144, and no water depth is published.
What they sayArctic's SMC fiberglass Forever Floor is 'impervious to moisture, pests, and time' and, Arctic says, removes the need for costly site set-up.
What the documents showIt's a genuinely rot-proof base, standard on the Ocean, Columbia, Okanagan and Polar Bear. But the other four models ship on pressure-treated wood unless upgraded, and the no-pad promise doesn't apply to swim spas.
Who else does itSealed bases are common (Master Spas' high-density polymer base and Jacuzzi's ProPolymer base, for example). Arctic's is SMC fiberglass, which it compares to a cargo ship's hull, and its Custom warranty card covers the Forever Floor for life on a solid level pad.
Applies to: Standard on Ocean, Columbia, Okanagan, Polar Bear; upgrade on Hudson, Wolverine, Kingfisher, Athabascan
The catch
On a swim spa it doesn't replace the concrete pad. Arctic's own Forever Floor page adds: 'A concrete pad is required for all All-Weather Pools with Forever Floor®'; its warranty requires a concrete pad or engineered deck for All-Weather Pools; and the four Gecko-pack models come on a pressure-treated wood floor as standard.
What they sayArctic's top warranty covers the shell for as long as the original owner has the spa, with 5 years of parts and on-site labor on equipment and plumbing.
What the documents showIt's in writing on the Custom card, which the 2026 manual applies to the Ocean and Okanagan. The four Classic-card models get 10 years, and Arctic doesn't say which card covers the Columbia or Polar Bear.
Who else does itLong structure terms are common among premium brands (35 years at PDC and lifetime on Artesian's TidalFit, for example).
Applies to: Ocean and Okanagan (Custom card per the 2026 manual)
The catch
Water loss only, $60 of labor a claim, and it ends when you sell. The shell term covers water loss from structural failure. Each approved claim gets at most $60 toward on-site labor, and travel is yours after the first 30 days. Removal, delivery and installation of a replacement spa, and any crane or deck removal, are also yours, and every warranty card ends when ownership transfers.
What they sayThe Total Access cedar cabinet comes off on every side, and with perimeter insulation instead of full foam the pumps, heater and plumbing stay reachable for repairs.
What the documents showThe manual confirms access doors on all four sides, and Total Access is standard on all eight models.
Who else does itPerimeter-insulated cabinets with reachable equipment are offered by several swim spa makers (Cal Spas, PDC, Wellis, Dynasty and American Whirlpool among them). Arctic's version has access doors on all four sides, per its manual, and a rival maker's comparison says it would be easy to repair and get access to over time.
Years of cover as Arctic Spas publishes them. Who pays labor, travel and removal matters as much as the years, so read the card before you sign.
Travel costs are the owner's except within the first 30 days and 100 km of the dealer. The warranty pays at most $60 toward on-site labor per approved claim. If Arctic replaces the spa, removal, delivery and installation costs are the owner's. Arctic isn't liable for removing decks, sunrooms or gazebos or for crane costs. Union-connection leaks are treated as owner-serviceable and excluded, as are freezing and other acts of nature. Any repair attempt by someone other than a factory-authorized dealer voids the warranty. Coverage ends when the spa is sold or leaves the country of purchase, and commercial use is excluded. Claims must be filed within ten days of finding a defect, and the warranty registered within 30 days of delivery. The Custom card adds that an All Weather Pool must sit on a concrete pad or a properly engineered deck.

14′ 5″ · jet current
10′ 7″ of open water

14′ 2″ · jet current
8′ 5″ of open water

14′ 6″ · jet current
9′ 9″ of open water

14′ 6″ · jet current
More like it14- and 15-foot swim spasSwim spa electrical requirementsSwim spa costBest swim spas
Like the Okanagan? We send you the price range, then one dealer near you. No other dealer gets your details unless you say so.