Endless Pools E500

The four E-Series models get Hydrodrive: one propeller on a 5 hp hydraulic unit, a current Endless puts at 21 inches wide and 16 deep, and a top pace of 1:08 per 100 yards. They start at $55,999. The X-Series uses four airless jets, three round plus a low 'river jet' for lift, on two 2.5 hp pumps trimmed by diverter valves. The R-Series uses three airless jets on one two-speed 2.5 hp pump, rated at 215 gallons a minute, and Endless pitches it for play and aquatic workouts.

Applies to: All nine models. E-Series (E500, E550, E700, E2000): propeller. X-Series (X500, X2000): four airless jets on two pumps. R-Series (R200, R220, R500): three airless jets on one two-speed pump.

What this means, and how to check it →endlesspools.com ↗endlesspools.com ↗

The compare tool lists interior dimensions as 'not available'. Architectural drawings from 2019 and 2020 print the lane from the current back to the seats or the rear wall: 6'6" on the R200, 7'6" on the E500, 9'5" on the X500, 9'6" on the E700 and R500, and 11'5.5" on the seatless E550. On the E2000 and X2000 the printed 12'0" and 13'0" run to the spa divider across the swim side's bench seat and steps, so they overstate the open lane; no drawing was found for the R220. Widths come in two kinds: the E-Series and X2000 drawings measure 5'10" (6'9" on the E550) from rim to rim, while the X500 (5'2"), R200 and R500 (5'0") drawings measure only the lane floor inside the side ledges, so the two sets can't be compared. Water is 46 inches deep in the 58-inch E500, E550 and E700, 48 inches in the 20-foot models and 40 inches in the 50-inch X500 and R-Series; the seatless, 94-inch-wide E550 is Endless's pick for breaststroke and butterfly.

Applies to: Printed open-lane lengths for E500, E550, E700, X500, R200 and R500; divider-to-current swim-side lengths for E2000 and X2000; nothing printed for the R220; depth for all nine models.

What this means, and how to check it →waves-console-watkins-wellness.s3.amazonaws.com ↗waves-console-watkins-wellness.s3.amazonaws.com ↗

Endless prints the frame gauge, which few makers do, and its spec sheets list a thermoformed ABS base pan under every model except the R200, whose own sheet we couldn't check. What's bonded behind the acrylic isn't published; the warranty only calls the shell 'plastic, thermoformed material'. The 10-year structure warranty is a no-leak promise: it pays for water lost through a shell defect, not for a crack that hasn't leaked.

Applies to: Steel frame: E500, E550, E700, E2000, X500, X2000. Wood frame: R200, R220, R500. ABS base pan confirmed on every model except the R200 (not stated in its reachable documents).

What this means, and how to check it →endlesspools.com ↗waves-console-watkins-wellness.s3.amazonaws.com ↗

The 2025 pre-delivery guide asks for a reinforced concrete pad at least six inches thick, says damage from an inadequate foundation isn't covered, and suggests an engineer before any elevated deck; filled weights run from 12,515 lb (R220) to 25,795 lb (E2000), counting 10 occupants. E and X models need a 60 A, 230 V breaker feeding the included GFCI subpanel, R models 30 A. On 60 A the E500, E550 and E700 heater stops while the jet pump runs (80 A fixes it), and the E2000 needs 110 A to run everything at once.

Applies to: All nine models.

What this means, and how to check it →waves-console-watkins-wellness.s3.amazonaws.com ↗endlesspools.com ↗

The E700 uses 70% of its California allowance and the R200 84%, with the E500 (432 W), E550 (501 W), X500 (464 W), R220 (351 W) and R500 (464 W) in between. The 20-foot E2000 and X2000 are listed as combination spas, and their listed figures (175 of 220 W) cover only the hot tub side. Endless calls its insulation a three-layer 'Tri-Thermic Barrier' without saying what the layers are; no heat pump appears on any product page, and single-zone models top out at 99°F.

Applies to: Standby figures: all seven single-zone models; E2000 and X2000 hot tub side only. Insulation: all models.

What this means, and how to check it →cacertappliances.energy.ca.gov ↗endlesspools.com ↗

Each zone gets its own 4 kW heater, circulation pump, filters, ozone unit and LCD control panel, and the spa side sets up to 104°F while Endless sells the E2000's swim side at 85°F. The catch is power: on the standard 60 A hookup the E2000's swim-side heater stops whenever the swim machine or treadmill runs, and the spa heater stops when both spa pumps run; everything at once takes 110 A. The other seven models are one body of water that can't be set above 99°F.

Applies to: E2000 and X2000. The E500, E550, E700, X500, R200, R220 and R500 are single-zone.

What this means, and how to check it →endlesspools.com ↗waves-console-watkins-wellness.s3.amazonaws.com ↗

Drawings recommend 2 feet of access around the whole spa; the equipment sits behind the seats on most models, under the control panel on the E550 and along the spa end of the 20-footers, and recessed installs need 36 inches of crawl space at the equipment door. On E-Series models the 2026 maintenance schedule calls for new hydraulic fluid and filter every 500 hours of use and a new submerged swim-machine motor, plus treadmill motor and belt, after six years. The warranty is void if anyone but Watkins' authorized representative attempts repairs, and it won't pay to remove a deck or reinstall the spa.

Applies to: All models; hydraulic maintenance applies to E-Series only.

What this means, and how to check it →waves-console-watkins-wellness.s3.amazonaws.com ↗endlesspools.com ↗

The E- and X-Series card gives 10 years against water loss from the shell, 7 on the surface and 5 on plumbing, components, heater and cabinet, with parts and labor paid but dealer travel charges possible. The Hydrodrive swim machine and the treadmill have separate two-year cards, and the R-Series card falls to 5 years on the surface and 3 on everything else. All of them end when the spa changes hands, exclude rentals, and won't pay to remove a deck or reinstall the spa.

Applies to: E-Series and X-Series card; Hydrodrive and treadmill cards (E-Series); RecSport card (R-Series).

What this means, and how to check it →endlesspools.com ↗endlesspools.com ↗

Every product page lists the Watkins cover, the Uprite lifter set, CoverCradle and Easy Slider as optional, so the starting prices include no cover or lifter, even though the FAQ says the swim spas 'come with covers'. Endless says its polyester cover won't absorb water but publishes no thickness, taper or density. California's listings name the cover each model was tested with, such as 305058C-X for the E500, so ask whether that's the cover you're getting.

Applies to: All nine models.

What this means, and how to check it →endlesspools.com ↗endlesspools.com ↗

Endless says it has over 250 retailers across North America for swim spa demos and service; warranty claims go to the selling dealer first, then to Watkins Wellness in Vista, California. Its manuals and warranties carry Watkins' Vista address, and its headquarters and factory showroom are near Philadelphia, but no source we found says which plant builds the swim spas. Ask the dealer where the model is made and who services the hydraulic drive.

Applies to: All nine models.

What this means, and how to check it →endlesspools.com ↗endlesspools.com ↗